| Odometer Display
|
Description
|
| GAGE |
Activates gauge
sweep of all gauges, then displays present gauge values. Also carries
out the checksum tests on ROM and EE. If the gauge sweep is inoperative,
INSTALL a new instrument cluster. |
| All segments
illuminated |
Illuminates all
odometer segments. If any odometer segment is inoperative INSTALL
a new instrument cluster. |
| bulb |
Illuminates all
micro-controlled indicators and LEDs. Install a new indicator or LED
as necessary. |
| r |
Returns to normal
operation of all micro-controlled indicators and LEDs and displays
hexadecimal value for ROM level. (used when requesting assistance
from the hotline). If alternating flashes for FAIL and ROM level are
displayed, INSTALL a new instrument cluster. |
| EE |
Displays the hexadecimal
value for EE level (used when requesting assistance from hotline).
If alternating flashes of FAIL and EE level are displayed replace
instrument cluster. |
| dt |
Displays hexadecimal
coding of final manufacturing test date (used when requesting assistance
from hotline). |
| dtc |
Displays continuous
DTC's in hexadecimal format. Pressing the SELECT/RESET button
will display any DTCs stored before proceeding to the next step. |
| enG |
Displays the English
speed in MPH. Speedometer will indicate present speed within tolerances.
Display will show 0 if input in not received. If input is invalid
for one second or more, or if speed is 0. |
| m |
Displays the metric
speed data in kph. Speedometer will indicate present speed within
tolerances. Display will show 0 if input in not received. If input
is invalid for one second or more, or if speed is 0. |
| tAc |
Displays the tachometer
data received from the PCM via the SCP network within tolerances.
Tachometer will indicate present RPM. Display will show 0 if input
is no received, if input received is invalid for one second or more,
or if engine RPM is 0. |
| FUEL |
Displays the code
(0-255) for the fuel sender input to the HEC. The fuel gauge will
display a filtered fuel level value. This filter will keep the pointer
from moving suddenly or erratically.
| 255 |
open send +/- 0 |
| 232 |
full stop +/- 0 |
| 215 |
Full mark +/- 10 |
| 178 |
3/4 mark +/- 8 |
| 138 |
1/2 mark +/- 7 |
| 93 |
1/4 mark +/- 5 |
| 41 |
E mark +/- 4 |
| 54 |
Low Fuel (0-59) |
| 0-18 |
short (0-20 max) |
|
| OIL |
Displays the code
(0-250) for the oil pressure switch input to the HEC. Oil pressure
gauge will indicate present oil pressure. Normal oil pressure (greater
than 6psi) will display a value between 000 and 176. A low oil pressure
or an inoperative engine oil pressure switch (less than 6 psi) will
display a value greater than 176. |
| dEGC |
Display of engine
temperature in Degrees C input from cylinder head temperature sensor.
| 49 C |
"C" mark |
| 60 C |
Normal band start |
| 120 C |
Normal band end |
| -40 C |
No SCP message for 5 seconds
|
|
| bAtt |
Displays the code
(0-255) for the battery voltage input to the HEC. Battery voltage
gauge will indicate present battery voltage.
| 93-102 |
6.2-9.1 volts, low voltage
|
| 115-124 |
8.5-10.7 volts, Normal band start
|
| 215-225 |
15.8-18 volts, Norm band end
|
| 230-241 |
16.9-19.1 volts, high voltage
|
|
| rhEo |
Displays the present
decimal rheostat dimming input, 0-255 (used when requesting assistance
from the hotline) |
rhi
rhS
rho |
Not used. |
| Cr |
Displays the current
RUN/START sense input. Display will show -h
for high input with the ignition switch in the START position
and -L for low input with the ignition switch
in the RUN position. |
| PA-PE7
|
not used. |
| GAGE |
Repeats the display
cycle |
| |
|
